RIA, PRO Match Tac Ultra in 10mm
Welcome to the Home of the 6.8 SPC - 68forums.com.
Results 1 to 6 of 6
  1. #1
    6.8 SPC Lover
    Join Date
    Feb 2012
    Location
    Texas
    Posts
    635

    Default RIA, PRO Match Tac Ultra in 10mm

    RIA, M1911 A2, Pro Match Tac Ultra, 10MM
    Model: 52,000
    HC Mag: 16 + 1 Round-
    Fit and Finish is excellent
    Average Trigger pull: 4.5lbs
    6" stainless bull barrel and guide rod
    AMBI SAFETY


    From Armscor's site:


    The PRO Match Ultra HC 6" is a target grade pistol ready for competition right out of the box. Built by the master gunsmiths in the Rock Island Armory Medallion, it's chambered in 10mm with a 16-round capacity and adjustable LPA rear sight and high visibility fiber optic front sight. It also includes a skeletonized hammer and factory 4- to 6-pound trigger with adjustable over travel stop. Comes in a fully parkerized finish with G10 grips. Add a full length picatinny tactical rail and the Pro Match Ultra HC is ready for any anything.









    She can definitely out shoot me.


    But I'm happy considering the following:


    1. Hornady 180grain XTP bullets average velocity 1360FPS
    2. Focused on not shooting my chrony
    3. Not use to a brass catcher mounted on a picatinny rail, but it caught all but one piece of brass.
    4. I. kept engaging the enlarged safety with my thumb, I started resting my thumb on top of the safety while trying to avoid the slide.


    On my next range trip, I'm going to take some sand bags and bench rest her to see what my (and the pistol) limitations are from 25 yards and beyond for hunting. I'm taking my Primos shooting sticks too.


    All excuses aside, here are the first ten shots:





    As time went on she got a little heavy (3.6lbs loaded, not counting brass catcher) and I got sloppy with trying double taps:





    My hunting load data:


    Light swipes and minor flatting of primers.


    Bullet: Hornady 180 gr XTP HP
    Case: Remington .985"
    Primer: WLP
    Powder: AA# 9 - 14.5 grains
    O.A.L: 1.260"
    Velocities: Average 1360fps

  2. #2
    68Forums.com lifer
    Join Date
    Apr 2008
    Location
    Tennessee
    Posts
    1,163

    Default

    That's one big pistol you got there, how thick are those grips?.............very nice. Just me but I would move to the 200 grainers if you decide to hunt with it.....wonder how/if it cycles the hard cast gas checks?? Send more range reports, there's always folks looking at the RIA offerings, including me at one time.
    '67 Tonkin Gulf Yacht Club, "Big Mothers"

  3. #3
    68Forums.com Team Member
    Join Date
    Aug 2009
    Location
    Big Island, HI
    Posts
    2,036

    Default

    Very nice, congrats. I'd like to add a RIA to my stuff one day.
    "Whiskey for my men, beer for my horses"

  4. Remove Advertisements
    68Forums.com
    Advertisements
     

  5. #4
    6.8 SPC Lover
    Join Date
    Nov 2014
    Location
    White Bear Lake Mn
    Posts
    686

    Default

    You mention the thumb safety as a rest. My 1911 is the same. I am having a discomfort with the ambi safety digging into my right hand index finger. I do not like the big safety levers. Also I would like a adjustable rear site for elevation for the way I site in. Other then this I am happy with my RI choice. What is the weight of the 10m empty??

  6. #5
    6.8 SPC Lover
    Join Date
    Feb 2012
    Location
    Texas
    Posts
    635

    Default

    I've ran 200gr XTP's and hard cast in a G20, G4 with KKM barrel. I prefer the 180gr over all performance.

    She weighs 2.7lbs unloaded. Even shooting hotter loads, this pistol basically has very little
    recoil.....similar to shooting a GP100 .357 6".

    Between work and other activities, I just haven't had the time to spend to master the pistol.

    PS: the two dot LPA adjustable rear sight is nice, but I'm going to change it out to Dawson's tritrium LPA adjustable rear and front sight.
    Last edited by TXCOONDOG; 08-10-2016 at 08:04 PM.

  7. #6
    6.8 SPC Lover
    Join Date
    Feb 2012
    Location
    Texas
    Posts
    635

    Default

    Picked up some 200 grain TC cast with a BHN of 16 sized at .401 from ACME and seeing some potential.


    Pistol: RIA Pro Match, Model 52,000
    Benchrest: 25 yds


    Bullet: 200 grain TC PB cast, .401"
    Lube: 45-45-10
    Case: Starline .985"
    Primer: WLP
    Powder: 8gr of Longshot
    COL: 1.250"
    Velocity: 1227 fps ES: 10 SD: 3


    30 shots at 25yds off the bench:




 

Search tags for this page

ria 52000

Click on a term to search for related topics.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •